lifestyle
What subsection of hair determines the length that the hair will be cut?
Written by Andrew Vasquez — 0 Views
Cards
| Term reference points | Definition In a haircut, design lines that are proportionate are established by using: |
|---|---|
| Term more graduation | Definition As a rule, the more you elevate the hair, the ____ you create. |
| Term guideline | Definition The section of hair that determines the length the hair will be cut is called the: |
Subsequently, one may also ask, how tightly the hair is pulled when cutting is referred to as?
How tightly the hair is pulled when cutting is referred to as: Tension. The level at which a blunt cut falls is called the: Weight line.
One may also ask, which tool is used to remove bulk from the hair? Cards
| Term reference points | Definition In a haircut, design lines that are proportionate are established by using: |
|---|---|
| Term thinning shears | Definition The tool used mainly to remove bulk from the hair is the: |
| Term cutting hand | Definition In general, the hand that does most of the work in haircutting is the: |
Also, where and how the hair is moved over the head?
Chapter 16 Haircutting (Book #3)
| A | B |
|---|---|
| The term used to describe how hair is moved over the head is | distribution |
| A method of cutting or thinning hair where the fingers and shears glide along the edge of the hair to remove length is | slide cutting |
What are the two most commonly used elevations in haircutting?
The two basic lines used in haircutting are straight and curved. Elevation creates graduations and layers and is usually described in degrees. In a blunt or one- length cut there is no elevation (0 degrees). Elevations below 90 degrees build weight; elevations of 90 degrees or higher remove weight or layer hair.
Related Question Answers
How should the hair be parted when cutting a blunt cut?
Begin at nape left side take horizontal parting 1/4 to 1/2 inch from hariline. Comb subsection from scalp to ends. Comb again stopping just above cutting line. Cut straight across against comb, keep shears horizontal and parellel to floor.When hair is layered at a high elevation what guide is used?
Haircutting| Question | Answer |
|---|---|
| When hair is layered at a high elevation, a(n) ___________ guide is used. | Interior |
| What is the space between 2 lines or surfaces that intersect at a given point called? | Angle |
| What is necessary to help control the hair & produce a more uniform cut | Sectioning |
What requires less tension cutting?
Area of the head between the apex and back of the parietal ridge. often found at the crown, these growth patterns require Less tension when cutting to compensate for where hair will be pushed up when dry. To divide the hair by parting into uniform working areas for control.What is another version of point cutting?
Another version of point cutting, creates chunkier effect. Uses tip of shears to snip out pieces if hair at random intervals.When performing a haircut on straight hair maximum tension is used for?
In the clipper-over-comb technique, the area you are cutting should be no wider than 3 inches. Wave pattern is the amount of movement in the hair strand. Maximum tension is used on straight hair to achieve precise lines.What is the highest point on the head?
The crown is the highest point on your scalp, toward the back of your head. It's also called the vertex.What happens when a client's head is improperly positioned for a blunt cut?
_________________________ is parting the haircut in the opposite way that you cut it, at the same elevation, to check for precision of line and shape. What happens when a client's head is improperly positioned with the head forward for a blunt cut? 1. The line will not fall as you cut it.What implement is used to create short tapers fades and flat tops?
ClippersWhich type of comb is used mainly to detangle hair?
The comb used mainly to detangle the hair is the - comb. 10. - point are points on the head that mark where the surface of the head changes or the behavior of the hair changers ,such as the ears , jawline , occipital bone, or apex.What is over direction in haircut?
Over-direction occurs when hair is pulled out of its natural position (either forward or backwards) and is used to create length or weight in a specific area. The shape you create is based on the type of over-direction you use. Elevation controls what technique you are using.When using clipper over comb technique you should?
Terms in this set (23)- When using the clipper-over-comb technique, you should:
- hold the comb stationary and cut the length against the comb.
- Which of the following is a technique that uses diagonal lines to create angles by cutting the ends with a slight increase or decrease in length?
Where is the clipper over comb usually performed?
To begin with, the comb should be held in the less dominant hand and used to lift hair at a 90 degree angle away from the scalp. The barber can then hold the clipper in the dominant hand and move up the comb, cutting off the hair protruding beyond the comb's teeth.What elevation is a long layered haircut?
If by "high-elevation haircut" you were referring to a "long-layered" haircut (in which all of the hair is held at 180-degree elevation and cut to a specified guide length) then you can find the instructions for this in our previous article on long layered haircuts. Are there different types of layering?Is created when the space between two lines or surfaces intersects at a given point?
Angle. The space between two lines or surfaces that intersect at a given point. Vertical Lines. Usually described in terms of up and down and are perpendicular to the floor, they are the opposite of horizontal.What are a razor haircutting shears styling or cutting comb and texturizing shears used for?
A razor is used when a softer effect on the ends of the hair is desired. Haircutting shears are mainly used to cut blunt or straight lines in hair. Styling and cutting combs are used for all purposes and texturizing shears are used to remove bulk from the hair.What tools are used for texturizing?
Short shears, long shears, blending shears and razors—they all have a purpose when it comes to texturizing hair.What is a finger Tang?
The hand movement (pushing with the thumb, pulling with the fingers) can add to this tension. Some scissors have an appendage, called a finger brace or finger tang, below the index finger hole for the middle finger to rest on to provide for better control and more power in precision cutting.What are the two types of guidelines in haircutting?
The two types of guidelines in haircutting are stationary and traveling. A stationary guideline does not move (Figure 16–19). All other sections are combed to the stationary guideline and cut at the same angle and length.Which hair cutting tool is mainly used to cut blunt or straight lines in hair?
haircutting shearsWhat does it mean to palm the shears?
Palming the shears how. Remove your thumb from the thumb grip leave your ring in little finger in the grip and finger rest. Curl your finger into palm the shears, this keeps the closed while you come or part the hair.What is the triangular section of the head?
Cards| Term ANGLE | Definition SPACE BETWEEN TWO LINES OR SURFACES THAT INTERSECT AT A GIVEN POINT. |
|---|---|
| Term APEX | Definition HIGHEST POINT ON THE TOP OF THE HEAD. |
| Term BANG | Definition TRIANGULAR SECTION THAT BEGINS AT THE APEX AND ENDS AT THE FRONT CORNERS. |
